Small Base ROCHESTER 2-Jet
2G - 2GC - 2GV Models

Rochester Tri-Power / 3-Deuce
Progressive Linkage & Base Plate Kits

Our Rochester Tri-Power / 3-Deuce Progressive Linkage & Base Plates
- “Basic Kit”

is designed for those who need to eliminate the vacuum leaks associated with using old base plates with poor fitting throttle blades and worn out shafts, and at the same time you get “The Best Progressive Linkage that
is available from any source ”

Includes =

• All 3 of Our Fully Assembled and Blue Printed Base Plates include the following features;

• Our NEW Extended Throttle Shafts with Full 5/16" Diameter Splined Ends

• Our Thick - Machined Throttle Blades (on the end carbs)

• Our Custom made Torsion Springs and Collars (on the end carbs)

• 3 Chrome Plated Throttle Arms
(1 primary and 2 custom end carb arms)

• 3 New Chrome Plated Accel. Pump Rods

• plus +

• Our "Splined - No-Slip - No-Bind" 3-Deuce / Tri-Power Progressive Linkage (that we set here for your intake spacing)
(realize this ain't no spindly 1950's coat hanger)

• plus + +

• 2 Power Valve Plugs

• 2 sets Air Horn Plugs

• 9 New Base Plate to Bowl Screws

• 3 New Bowl Gaskets

• 3 Base Plate Gaskets

• 3 Base Plate to Intake Gaskets

ALL of the above is also included in Our Master Builder Kit to the Right

(you must have your own small base
Rochester 2G - 2GC - 2GV carbs)

featured in Hot Rod Magazine Feb.'11

(reg. $645) sell @ $595.00

Our Rochester Tri-Power / 3-Deuce Progressive Linkage & Base Plates
- “Master Builder Kit”

is designed for the Do-It-Yourselfer who has some common primary carburetor cores and wants to build them into a correct and properly functioning set of Tri-Power.

(these are all of the same parts and pieces that we use in our custom system builds)

Includes =

• Everything in the “Basic Kit” to the Left

• Plus + + +

• 3 Complete Rebuild Kits - that includes Our Ethanol / Methanol Resistant Accelerator Pump Assemblies and all small parts

• All Gaskets including Our Custom
Cut & Coated Bowl & Base Gaskets

• 1 New Power Valve

• 1 New Modified Power Piston

• 3 Pair of New Correct Jets -
for your engine and application

- 1 pair Primary Carb

- 2 pairs Secondary Carbs

• 3 New Brass Floats with Pins

• 3 Air Cleaner Gaskets

This is the 'Best Buy' for
the Do-It-Yourselfer

(you must have your own small base
Rochester 2G - 2GC - 2GV carbs)

(the intake manifold; oil fill tube with breather; carbs to intake manifold mounting studs & nuts shown are all available separately)

featured in Hot Rod Magazine Feb.'11

(reg. $895) sell @ $795.00

4-Deuce Man-A-Fre & Offenhauser
Cross Shaft 1:1 Linkage KIT includes;

• 1 Splined Cross Shaft
• 2 Cross Shaft Supporting Rod Ends **
• 2 Cross Shaft Throttle Arms
• 3 Black Centering Collars
• 4 - 9 3/4" long Hex Links
• 4 Right Hand Rod Ends
• 4 Left Hand Rod Ends
• 6 Anti-Rotation Washers
• Misc Screws & Hardware

** Offy Apps we supply the 2 required Rod End Stanchions

• Realize this is a parts kit that will require total assembly by You the end user. We do include an assembly diagram, but you'll have to do lay out - measure - cut - tap - and weld, when necessary.

Offy version w/stanchions @ $250.00

Man-A-Fre version @ $225.00

Simple, Clean, and Easy To Install!

This photo shows the bracket and cables when joined

Small Base Rochester 2G Specific

Throttle Return and Cable Bracket
comes with dual return springs and
the 2 required carb base gaskets*

*we include these, nobody else does this!!

these are standard in our completely assembled systems

each kit = $54.00

24" Accelerator Cable

with Black Vinyl Sheath...

Much easier to keep clean than braided stainless steel and it's got that simple O.E.M. look!

each @ $45.00

Transmission Specific Kick-Down Cables

with Black Vinyl Sheath...

Much easier to keep clean than braided stainless steel and it's got that simple O.E.M. look!

each starting @ $80.00